The interaction of non-monochromatic radiation with arrays comprising plasmonic and dielectric nanoparticles has been studied using the finite-difference time-domain electrodynamics method. It is shown that LiNbO3, TiO2, GaAs, Si, and Ge all-dielectric nanoparticle arrays can provide a complete selective reflection of an incident plane wave within a narrow spectral line of collective lattice resonance with a Q-factor of 103 or larger at various spectral ranges, while plasmonic refractory TiN and chemically stable Au nanoparticle arrays provide high-Q resonances with moderate reflectivity. Arrays with fixed dimensional parameters make it possible to fine-tune the position of a selected resonant spectral line by tilting the array relative to the direction of the incident radiation. These effects provide grounds for engineering novel selective tunable optical high-Q filters in a wide range of wavelengths, from visible to middle-IR.An effective experiment scheme is proposed to generate the terahertz (THz) perfect optical vortex (POV) beams by diffractive elements at the frequency of 0.1THz. Two diffractive elements are designed and fabricated by 3D-printing to form the generation system. The ring radius of the generated beams is independent of the topological charge and positive linear relationship with the radial wave vector. By controlling the radial wave vector, the ring radius can be freely adjusted. The experiment results are shown to corroborate the numerical simulation ones. Such generated beams hold promise for developing the novel THz fiber communication systems.The calibration and sampling of the multispectral Light Detection and Ranging (lidar) intensity is still challenging because the data acquisition has to be optimized for simultaneous 3D measurement, and the intensity retrieval methods need to be fast to enable real-time detection. We have studied the spectral measurement of low reflectance targets with an 8-channel hyperspectral lidar with improved waveform sampling and sensitivity, which now allow the detection of spectral differences even at low reflectance values. Our initial analysis resulted in a classification accuracy greater than 80%, which indicates that the multispectral lidar is able to detect the small differences in target spectral properties when reflectance at two or more channels is compared at the same time.Holes through silicon substrates are used in silicon microsystems, for example in vertical electrical interconnects. In comparison to deep reactive ion etching, laser drilling is a versatile method for forming these holes, but laser drilling suffers from poor hole quality. In this article, water is used in the silicon drilling process to remove debris and the shape deformations of the holes. Water is introduced into the drilling process through the backside of the substrate to minimize negative effects to the drilling process. Drilling of inclined holes is also demonstrated. The inclined holes could find applications in radio frequency devices.In this article, based on nonadiabatic molecular dynamics with electronic transitions, the elaborate ultrafast process of hot excitons in conjugated polymer solar cells is revealed. When an external optical beam/pulse with the intensity of 30 µJ/cm-2 is utilized to excite a conjugated polymer, just within only 50 fs, the electronic transition not only redistributes the electron population in the original molecular orbital, but also starts to localize the electron cloud of excited states and to distort the alternating bonds in the polymer chain. Up to 300 fs, the lattice distortion has been stabilized. During the formation of hot excitons, the prominent self-trapping effect of conjugated polymer triggers the occurrence of local infrared active phonon modes, with five peaks in the phonon spectrum as the hot excitons relax. The characteristic phonon spectrum and infrared modes hence form the fingerprint of the hot excitons of a conjugated polymer, which are readily distinguished from other excitation states in the polymer.Frequency combs in the mid-IR wavelength are usually implemented by difference-frequency generation (DFG) that mixes pump pulses and signal pulses. Different from most optical parametric amplifiers that operate at a typical low repetition rate of 2 W) longwave mid-IR frequency combs is practically feasible.Plasmonic nanostructures hold great promise for enabling advanced optical manipulation of nanoparticles in microfluidic channels, resulting from the generation of strong and controllable light focal points at the nanoscale. A primary remaining challenge in the current integration of plasmonics and microfluidics is to transport trapped nanoparticles along designated routes. Here we demonstrate through numerical simulation a plasmonic nanoparticle router that can trap and route a nanoparticle in a microfluidic channel with a continuous fluidic flow. The nanoparticle router contains a series of gold nanostrips on top of a continuous gold film. The nanostrips support both localised and propagating surface plasmons under light illumination, which underpin the trapping and routing functionalities. The nanoparticle guiding at a Y-branch junction is enabled by a small change of 50 nm in the wavelength of incident light.We present a foveated rendering method to accelerate the amplitude-only computer-generated hologram (AO-CGH) calculation in a holographic near-eye 3D display. For a given target image, we compute a high-resolution foveal region and a low-resolution peripheral region with dramatically reduced pixel numbers. Our technique significantly improves the computation speed of the AO-CGH while maintaining the perceived image quality in the fovea. Moreover, to accommodate the eye gaze angle change, we develop an algorithm to laterally shift the foveal image with negligible extra computational cost. this website Our technique holds great promise in advancing the holographic 3D display in real-time use.We present a scanning light detection and ranging (LIDAR) system incorporating an individual Ge-on-Si single-photon avalanche diode (SPAD) detector for depth and intensity imaging in the short-wavelength infrared region. The time-correlated single-photon counting technique was used to determine the return photon time-of-flight for target depth information. In laboratory demonstrations, depth and intensity reconstructions were made of targets at short range, using advanced image processing algorithms tailored for the analysis of single-photon time-of-flight data. These laboratory measurements were used to predict the performance of the single-photon LIDAR system at longer ranges, providing estimations that sub-milliwatt average power levels would be required for kilometer range depth measurements.