05.

Hydrothermal aging caused reduction in mechanical properties such as surface hardness, biaxial flexural strength, and fracture toughness of Y-TZP zirconia. However, cubic-containing zirconia (more than 30% by volume of cubic crystal) was assumed to have high resistance to hydrothermal degradation. selleck chemical Clinical significance Cubic-containing zirconia could withstand the intraoral aging condition. It could be suggested to use as a material for fabrication of esthetic dental restoration.

Hydrothermal aging caused reduction in mechanical properties such as surface hardness, biaxial flexural strength, and fracture toughness of Y-TZP zirconia. However, cubic-containing zirconia (more than 30% by volume of cubic crystal) was assumed to have high resistance to hydrothermal degradation. Clinical significance Cubic-containing zirconia could withstand the intraoral aging condition. It could be suggested to use as a material for fabrication of esthetic dental restoration.

The aim of this study was to investigate and compare the color stability of provisional restorative materials fabricated by 3D printing, dental milling, and conventional materials.

For the experimental groups, two commercially available 3D-printing provisional resins (E-Dent 100; EnvisionTEC GmbH, Germany & VeroGlaze™; Stratasys®, USA), two dental milling blocks (PMMA Disk; Yamahachi Dental Co., Japan & Telio®CAD; Ivoclar Vivadent AG, Liechtenstein), and two conventional materials (Alike™; GC Co., Japan & Luxatemp automix plus; DMG, Germany) were used. The water sorption and solubility test were (n=10, respectively) carried out according to ISO40492000 (International Standards Organization, Geneva, Switzerland). For the color stability test (n=10), coffee and black tea were used as staining solutions, and the specimens were stored for 12 weeks. Data were analyzed by one-way ANOVA and Tukey’s HSD using SPSS version 22.0 (SPSS Inc. Chicago, IL, USA) (

<.05).

Alike and Veroglaze showed the highest values and Luxatemp showed the lowest water sorption. In the color stability test, the ΔE of conventional materials varied depending on the staining solution. PMMA milling blocks showed a relatively low ΔE up to 4 weeks, and then significantly increased after 8 weeks (

<.05). 3D-printed materials exhibited a high ΔE or a significant increase over time (

<.05).

The degree of discoloration increased with time, and a visually perceptible color difference value (ΔE) was shown regardless of the materials and solutions. PMMA milled and 3 D-printed materials showed more rapid change in discoloration after 8 weeks.

The degree of discoloration increased with time, and a visually perceptible color difference value (ΔE) was shown regardless of the materials and solutions. PMMA milled and 3 D-printed materials showed more rapid change in discoloration after 8 weeks.

The bond strengths between resin denture teeth with various compositions and denture base resins including conventional and AD/CAM purposed materials were evaluated to find influence of each material.

Cylindrical rods (6.0 mm diameter × 8.0 mm length) prepared from pre-polymerized CAD/CAM denture base resin blocks (PMMA Block-pink; Huge Dental Material, Vipi Block-Pink; Vipi Industria) were bonded to the basal surface of resin teeth from three different companies (VITA MFT®; VITA Zahnfabrik, Endura Posterio®; SHOFU Dental, Duracross Physio®; Nissin Dental Products Inc.) using resin cement (Super-Bond C&B; SUN MEDICAL). As a control group, rods from a conventional heat-polymerizing denture base resin (Vertex™ Rapid Simplified; Vertex-Dental B.V. Co.) were attached to the resin teeth using the conventional flasking and curing method. Furthermore, the effect of air abrasion was studied with the highly cross-linked resin teeth (VITA MFT®) groups. The shear bond strengths were measured, and then the fractured surfaces were examined to analyze the mode of failure.

The shear bond strengths of the conventional heat-polymerizing PMMA denture resin group and the CAD/CAM denture base resin groups were similar. Air abrasion to VITA MFT® did not improve shear bond strengths. Interfacial failure was the dominant cause of failure for all specimens.

Shear bond strengths of CAD/CAM denture base materials and resin denture teeth using resin cement are comparable to those of conventional methods.

Shear bond strengths of CAD/CAM denture base materials and resin denture teeth using resin cement are comparable to those of conventional methods.A once-annual caries preventive (Intervention) treatment was offered to Aboriginal and Torres Strait Islander schoolchildren-a population with disproportionately poorer oral health than non-Indigenous Australian children-in the Northern Peninsula Area (NPA) of Far North Queensland (FNQ), which significantly improved their oral health. Here, we examine the salivary microbiota of these children (mean age = 10 ± 2.96 years; n = 103), reconstructing the bacterial community composition with high-throughput sequencing of the V4 region of bacterial 16S rRNA gene. Microbial communities of children who received the Intervention had lower taxonomic diversity than those who did not receive treatment (Shannon, p less then 0.05). Moreover, the Intervention resulted in further decreased microbial diversity in children with active carious lesions existing at the time of saliva collection. Microbial species associated with caries were detected; Lactobacillus salivarius, Lactobacillus reuteri, Lactobacillus gasseri, Prevotella multisaccharivorax, Parascardovia denticolens, and Mitsuokella HMT 131 were significantly increased (p less then 0.05) in children with severe caries, especially in children who did not receive the Intervention. These insights into microbial associations and community differences prompt future considerations to the mechanisms behind caries-preventive therapy induced change; important for understanding the long-term implications of like treatment to improve oral health disparities within Australia. Trial registration ANZCTR, ACTRN12615000693527. Registered 3 July 2015, https//www.anzctr.org.au/Trial/Registration/TrialReview.aspx?id=368750&isReview=true.